Civil Technology Woodworking Paper 1 (English)

May-June 2019 — Grade 12 / Matric — Civil Technology

Past Paper 2019 Grade 12 English

↓ Download PDF 📄 669.3 KB View Memorandum

Preparing document

📋 Document Analysis

🎯 200 marks 📄 16 pages 📝 77 items found ∑ 1 math symbols 📚 1 topics

See full analysis

Questions — A Preview of What to Expect in the Document

This section provides a quick preview of questions from the document. It may not display every question or the complete wording of each one. For the full content, including diagrams, tables and other information, view the original PDF above.

Q1— Section header —

1.1Choose a description from COLUMN B that matches an item in COLUMN A. Write only the letter (A G\next to the question numbers (1.1.1 to 1.1.5\in the ANSWER BOOK , e.g. 1.1.6 H. COLUMN A

1.1.5Galvanising Electroplating Curing Paint Powder coating

1.2Explain ONE cause of injuries wh en handling materials. (1\

1.3Give the angle/ratio at which a ladder should be placed against a wall. (2\

1.4Explain TWO safety precautions that must be followed when using a builder's hoist. (2\ Civil Te ch nolog

1.5FIGURE 1.5 below shows tools that are u sed on a construction site. FIGURE 1.5

1.5.1Identify both and (2\

1.5.2Name ONE use of and respectively. (2\

1.6The pictures below illustrate the steps followed when fixing ma terial to a floor with a fastener. FIGURE 1.3

1.6.1Identify the fastener that is used in (1\

1.6.2Describe the steps in above in your ANSWER BOOK. (4\

1.6.3Justify the u se of this fastener to secure the bracket of a heavy gate to a wall. (1\ [20]20

Q2— Section header —

Q3— Section header —

3.1Name the part of a casement that separates two window panes so that they do not touch each other. (1\

3.2FIGURE 3.2 below shows an external elevation of a double casement with fanlights. Name parts FIGU UR 3.

3.2(5\ Civil Te

3.3FIGURE 3.3 below shows the front view of a built in cupboard without the doors. Use ANSWER SHEET 3.3 and draw a vertical sectional view of the cupboard to scale 1 10. FIG

3.3Use the following spec ifi tions All shelves and sides are 16 mm

3.5FIGURE 3.5 below shows the floor plan of a building with a gable roof. The centre to centre distance between the roof trusses is 1 300 mm. Study

3.5.2Calculate the length in metres of fascia board needed for the whole roof. Calculate the number of trusses needed for the r oof. (2\

Q4— Section header —

4.1Choose a term from COLUMN B that matches a roof in COLUMN A. Write only the letter (A G\ next to the question numbers (4.1.1 to 4.1.5\in the ANSWER BOOK, e.g. 4.1.6 H. OL

4.1.1lean to roof

4.1.2couple roof

4.1.3king post roof

4.1.4collar tie roof

4.1.5outh Afri an (Howe\ roof

4.2Use ANSWER SHEET 4.2 and complete the vertical section through the foot of a roof truss by drawing the closed eave to scale 1 10. Show the following on your drawing: Fascia board

4.3Differentiate between a hipped roof and a gable roof in terms of the quantity of material and the type of construction used. Tabulate your answer. (4\

4.4Name THREE different methods of joining roof truss members to each other. (3\

4.5Name TWO components that can be used to keep a trap door of a ceiling in position. (2\ .6 Give the minimum measurements for the opening of a trap door. (1\

4.7FIGURE 4.7 below shows a portable electrical machine . Study the picture and answer the questions that follow. FIGUR

4.7.3Identify th e machine. Name TWO personal safety equipment that you must be wearing when operating this machine. Explain how you will store the machine. (1\ (2\

4.7.4Explain TWO precautions that should be applied to a piece of timber to prevent damages to the machine shown in FIGURE 4.7. (2\ Civil

4.8FIGURE 4.8 shows a radial arm saw. Study the picture and answer the questions that follow FIGUR

4.8.2Describe THREE precautions that should be taken to ensure the safe handling of the machine. Explain how the blade of the machine must be cared for to prevent it

4.9Explain in FIVE steps how you will apply two layers of sanding sealer to a door that has been sanded smooth. (5

4.10Explain how you will recogni e a graded timber plank/board. (1\ [40] Civil Te ch nolog40

5.1Draw a neat two dimen sional sketch to show the open laggings, rib and a bearer to support a segmental arch. Show the following on your drawing: Bearer Rib

5.2Give ONE word/term for eac h of the following descriptions by choosing a word/term from the list below. Write only the word/term next to the question numbers (5.2.1 to 5.2.5\the ANSWER BOOK, e.g. 5.2.6 Riser.

5.2.1Fixed diagonally to the struts/props and head tree to strengthen the formwork (1\

5.2.2To fix the props and bearer together (1\

5.2.3Fixed to the beam sides to make them stronger (1\

5.2.4Placed under the props to allow the raising and lowering of the formwork to the required height (1\

5.2.5Transfers the load of the concrete beam evenly to the ground (1\

5.3Name TWO types of material that can be used for the lining on the inside of formwork. 2\ Civil Te ch nolog

5.4FIGURE 5.4 below shows the formwork for a square concrete column. Study the picture and label parts and FIGUR

5.4(3\

5.5Draw a neat two dimensional sketch in good proportion of the detail at the base of a dead shore.

5.6Use ANSWER SHEET 5.6 and draw a neat two dimensional sketch in good proportion of a lean

6.1Various options are given a s possible answers to the following questions. Choose the answer and write only the letter (A D\ next to the question numbers (6.1.1 to 6.1.5\the ANSWER BOOK, e.g. 6.1.6 C.

6.1.1Floorboards are attached to floor joists that are supported by ... struts that are resting on tie beams. props every 3 met es.

6.1.2Ant guards are made from galvanised steel and placed ... underneath the wall plate. inside the air brick s.

6.1.3The width of a floor board should be at least 50 mm and not exceed ... 100 mm. 400 mm.

6.1.4Floor boards should have a ... joint. tongue and groo

6.1.5nails. screws. truss hanger. All

6.2Use ANSWER SHEET 6.2 and draw in good proportion a sectional view of the external wall that supports a suspended timber floor. The foundation is given. Show the f

6.3Explain a half landing as used in a timber staircase. (3\

6.4Explain the difference between a mortice lock and a night latch with regard to their placement and function. (4\

6.6FIGURE 6.6 on ANSWER SHEET 6.6 shows the incomplete front view of a double tenon . Use ANSWER SHEET 6.6 and complete the drawing of the double tenon. Show the following on your drawing:

6.7FIGURE 6.7 below shows a fastener used to join materials. Identify the fastener. FIGUR

6.7(1\

6.5FIGURE 6.5 on ANSWER SHEET 6.5 shows an external view of a n external door. Use ANSWER SHEET 6.5 and complete the following Print any FOUR labels on the drawing

6.8Name ONE fastener to join the following:

6.8.1Ceiling boards to bran dering (1\

6.8.2Roof tiles to battens (1\

6.8.3Roof sheeting to purlins (1\

6.9State ONE method of fixing window pane to a frame. (1\ [40] TOTAL: 200 Civil Te40

3.5.1Length of fascia board = _______mm = _______m

3.5.2Number of roof trusses needed Internal dimension Distance between centres ____________ ____________ = ____________ + 1

4.2ASSESSMENT CRITERIA MARK CANDIDATE'S MARK Fascia board 230 mm x 38 mm Hanger

6.2ENTR ER: ASSESSMENT CRITERIA

6.5FI GUR

6.5ENTR ER: Civil

6.6ENTR ER: ASSESSMENT CRITERIA

Mathematical Content

f(x)

Topics Identified

Construction

Mark Allocation

Total200 marks

Sections20 + 40 + 30 + 40 + 30 + 40 = 200 marks

Paper information

SubjectCivil Technology

Year2019

SessionMay-June

TypePast Paper

PaperPaper 1

LanguageEnglish

Pages27

Downloads12

Examination context

Decade2010s

Years ago7y

Season—

Start day—

Exam period—

Days since exam—

About Civil Technology examination preparation

This Grade 12 examination resource can be used as part of a structured revision programme. Past papers are most useful when learners attempt questions independently, work within a realistic time limit, and review their answers afterwards.

How to use this resource for revision

A past examination paper is most useful when it is treated as an active revision exercise. Try the questions yourself before checking the corresponding memorandum. Where you make an error, identify the reason — was it a knowledge gap, a calculation mistake, an interpretation issue, or an examination technique problem?

For stronger examination practice, complete the paper without unnecessary interruptions and keep track of the questions that take the most time. Afterwards, review the memorandum and separate knowledge gaps from mistakes caused by interpretation, calculation, structure, or examination technique.

understanding question requirements

applying subject knowledge

working under time constraints

checking answers

identifying revision priorities

A practical revision approach

Start by completing the resource without looking at the memorandum. Review incorrect and incomplete answers afterwards and make a short revision list based on the areas that caused difficulty.

Grade 12 subject hubs

Each matric subject has its own dedicated hub on Freemode with every past paper and marking memorandum we have archived for that subject.

➗ Mathematics View papers → 📊 Mathematical Literacy View papers → ⚗️ Physical Sciences View papers → 🧬 Life Sciences View papers → 📒 Accounting View papers → 💼 Business Studies View papers → 📈 Economics View papers → 🌍 Geography View papers → 🏛️ History View papers → 📖 English View papers → 🇿🇦 Afrikaans View papers → 🗣️ IsiNdebele View papers → 🗣️ IsiXhosa View papers → 🗣️ IsiZulu View papers → 🗣️ Sepedi View papers → 🗣️ Sesotho View papers → 🗣️ Setswana View papers → 🌾 Agricultural Sciences View papers →

Corresponding marking memorandum

Marking memorandum available

Use the corresponding memorandum after completing the paper to review your answers and identify areas that require further revision. The memorandum shows the marking approach used by DBE examiners, including method-mark allocations.

Civil Technology Woodworking Memo 1 (English) →

File details

File size669.3 KB

Pages27

Archived on11 October 2026

File age14d

ContributorFreeMode

Fingerprint46EBF906C161

Questions and learner discussion

No questions or discussions have been posted yet.